!

Little Lunar Express
!
Larger picture
PML has taken rocketry back to the future with this kit! Based on the rockets of 1950`s SciFi movies, here`s the Little Lunar Express! With it`s fin "wings" and tail, landing pods, and retro styling, this is one great-looking bird. First shown to the world at LDRS-17 and NARAM-40, this kit has all the great features you`ve come to expect from PML. Complete with cockpit and passenger window decals, as well as tail numbers. This 3.9" diameter rocket has the same standard high-quality features that go into every PML kit: G10 fins, piston ejection system, preslotted tailcone, and more. This is a great kit to add to your collection, and is sure to draw attention on the flying field! Flies great on 38mm H and I motors and 29mm motors with ADPTR-38/29.

  • Motor based recovery system
  • Plastic nose cone and boattail
  • 0.062 G-10 fins
  • 38mm motor mount (can be flown on 29mm motors using the optional ADPTR-38/29 motor adapter)
  • Molded urethane landing pods
  • 54" heavy-duty parachute
  • Stands nearly 3 feet tall
  • Complete, three color decal set and detailed instructions

Dia.: 3.9
Height: 35"
Weight: 58 oz.
MMT: 38mm

Endeavour
!
Larger picture
A unique and scale like rocket featuring a split fin design similar to those found on the most advanced air-to-air missiles. Flies on H through J motors. Complete with a "Kwik-Switch" motor mount.

  • Pre-slotted Quantum Tube airframe
  • G-10 Fiberglass fins
  • Kwik-Switch motor mount
  • Piston ejection system
  • 18" Payload Bay
  • Multi-panel nylon parachute
  • Plastic nose cone
  • Thin-wall brass launch lug
  • Explicit instructions remove guesswork

Dia.: 3.9"
Height: 71"
Weight: 71oz.
MMT: 54/38/29mm Kwik-Switch

Tethys
!
Larger picture
The perfect first large-diameter bird at 3.9" diameter. Easy to build, with advanced features like a Kwik-Switch 2000 motor mount and multi-panel parachute. This 53-inch tall beauty flies on G through J motors.
Dia.: 3.9"
Height: 53"
Weight: 53 oz.
MMT: 54/38/29mm Kwik-Switch

Tiny Pterodactyl
!
Larger picture
A new generation of Pterodactyls is born! Like it’s parent the mighty Pterodactyl and sibling Pterodactyl Jr., the Tiny Pterodactyl was born to fly. Use an F motor for slow, graceful flights or pack it with a G motor for real excitement. We’ve even flown the Tiny Pterodactyl on an H-238 and amazed the crowd with a neck snapping transonic flight!*

* Nose weight was added to keep the CG forward of the CP during this flight. Some rocketeers like to keep two nosecones on hand: one weighted for higher power motors and a standard one for lower power flights.

Comes with an 18" chute, QT airframe, piston system, decal, and 0.062 G-10 fins.

Dia.: 2.1"
Height: 25.5"
Weight: 18 oz.
MMT: 29mm

Pterodactyl, Jr.
!
Larger picture
The Pterodactyl, Jr., an offspring of the mighty Pterodactyl, is half the size and just as eager to fly.

With its 38mm motor mount, the Pterodactyl, Jr. can soar to great heights using Easy Access motors. Comes with a 36" chute, decals, and 0.062 G-10 fins.

Dia.: 3.9"
Height: 41"
Weight: 39 oz.
MMT: 38mm

Quantum Leap II
!
Larger picture
PML`s "quantum mechanics" have continued to improve one of rocketry`s favorite two-stagers, the Quantum Leap. The new Quantum Leap II, now with the new Interstage 3000 staging adapter system, is a completely modular two stage rocket. Once you assemble the four basic components, you can combine them to make any of five rocket combinations and can change to any configuration in minutes. The new Interstage 3000 system is much easier to prep and use than the previous interstage coupler design, and is identical in design to the IS3000 used in the Terrier booster stage for our MiniBBX. The IS3000 comes complete with timer mounts and remote safety switch.

This 2-stage rocket kit is intended for the experienced HPR scratch builder intending to supply his/her own electronic parachute deployment system into the sustainer stage. We strongly urge you not to fly this kit without an electronic parachute deployment system installed into the sustainer stage. Failure to do so will allow the sustainer stage to fall to earth without recovery deployment if the sustainer motor fails to ignite. If you are unsure about designing and installing your own electronic parachute deployment system, consider buying the Quantum Leap 3000 kit, which contains the electronic deployment components (except altimeter) as standard. To purchase a Quantum Leap 3000 kit already equipped with the CPR3000 Dual-Deployment Recovery System,

NOTE: The following chart lists configurations of this kit that may be flown as it is received stock from PML. However, your addition of an electronic deployment system may/will make some of these configurations unavailable, depending upon the design of your system.

Configuration Components Length Weight
##		 CP Notes
A 1,3,5 49.25" 49 oz. 43" Booster stage requires use of payload section for stability
B 1,2 49.25" 46 oz. 39.5"
C 1,3,2 61.25" 53 oz. 50.5"
D 1,2,4,5 75.75" 88 oz. 53.5" Upper stage requires electronic ignition **
E 1,3,2,4,5 87.75" 95 oz. 65" Upper stage requires electronic ignition **
COMPONENTS LIST AND NOTES
  1. Nosecone
  2. Upper (sustainer) stage
  3. Payload section
  4. Interstage coupler/staging timer housing
  5. Booster stage
** PML AccuFire Timer recommended for upper stage ignition; see in webstore. (Can also use Transolve ST-2B).
## Your weight may vary according to how much epoxy and paint you use when you build. Also does not include weight of staging timer (if required).

AGM-600 PitBull
!
Larger picture

The AGM-600 is a large 6" version of our AGM-256 PitBull The AGM-600 PitBull comes complete with fiberglass nosecone and boattail. The 54mm motor mount can handle any motor up to about 30" long, and comes with a 72" `chute for motor-based recovery. Also included are 0.093" G10 fins, PML`s piston ejection system, and of course the attention to quality and detail that sets PML ahead of the pack!

The CPR-MAX Electronic Recovery System cannot be added to the AGM-600 without major modifications that make it unfeasible. Sorry.

Dia.: 6.0 in.
Height: 79 in.
Weight: 193 oz.
MMT: 54mm

Bulldog
!
Larger picture
The Bulldog is a great "semi-scale" representation of the famous Bullpup missile. The Bulldog comes standard with two great PML hand-laid fiberglass nosecones (with one converted to a pre-slotted boattail for an easy build, great looks, and super drag-reducing performance), a 54mm motor mount, 0.093" G-10 fins, and a 72" parachute. The `Dog can fly on motors from a J180 through a K700 stock! The Bulldog has the usual PML high quality features of a phenolic airframe, piston ejection system, tubular nylon shock cord, and more.

The CPR-MAX Electronic Recovery System cannot be added to the Bulldog without major modifications that make it unfeasible. Sorry.

Dia.: 6.0 in.
Height: 74 in.
Weight: 170 oz.
MMT: 54

Ultimate Endeavour
!
Larger picture
If bigger is better and clustering is the key to your high power excitement, then the ULTIMATE Endeavour is the ticket!

Straightforward construction and excellent flight stability are combined with military styling to provide you with quick access to the world of large scale high power rocketry. Initial flights can be accomplished with a single 54mm motor. When you are ready to kick it in the butt, you can add a cluster of 38mm motors to the central 54mm for a real neck-snapping launch!

The payload bay on the Ultimate Endeavour measures 36" in length.

Dia.: 6.0 in.
Height: 108 in.
Weight: 173 oz.
MMT: 54mm w/(3) 38mm